http://www.loc.gov/mods/v3 http://www.loc.gov/standards/mods/v3/mods-3-2.xsd
Frontier in functional manufacturing technologies
selected, peer reviewed papers from the 2nd International Conference on Functional Manufacturing Technologies (ICFMT 2010), Aug. 6-9 2010, Harbin, Heilongjiang, China
2nd International Conference on Functional Manufacturing Technologies
International Conference on Functional Manufacturing Technologies 2010 : Harbin, China)
1 online resource (x, 327 pages) : illustrations
The major topics covered by the special volumes include anti-fatigue design and anti-fatigue manufacturing, manufacturing systems and reliability, processing detection and monitoring-control, CIMS and management systems, production system and simulation technology, quality control of manufacturing systems, agile manufacturing, finite-element analysis and structure optimization, digital manufacturing and robotics, rapid prototyping technology, reverse engineering technology, high-speed (ultra high-speed) precise cutting technology, ultra-precise processing technology, micro machining technology, pattern recognition technology, image processing technology, sensor and signal detection technology, non traditional machining technology, mine equipment manufacturing and technology, advanced manufacturing system and technologies and so on.
Preface -- Effect of Rare Earth Ce on Casting Properties of Al-4.5Cu Alloy -- Simulation and Experimental Investigations of Fiber Diameter of Spunbonding Nonwovens by Means of the Air Jet Flow Field Model -- Numerical Simulation of Accumulative Forming Bipolar Plates of Fuel Cell -- Low Temperature Synthesis and Luminescent Properties of Ca₂SnO₄: Eu³ -- Study on Load-Velocity Dynamic Property of Piston-Type Hydraulic Cylinder Based on SIMULINK -- Study on Formability about ME20M Magnesium Alloy Sheet -- Effect of Adding Er on Interfacial Reactions between Sn-3.0Ag-0.5Cu Solder and Cu Substrate -- Ocular Aberrations Measurement Combined with Subjective Visual Compensation -- Analysis of the Milling Distortion Due to Residual Stress Based on FEM -- Research of Thermodynamics and Properties of Pb/WC-Zro₂ Inert Electrodes Used in Zinc Electrodeposition -- Study on Influence Scope of Shock Wave and Smoke Flow after Gas Explosion -- Fabrication of Biodegradable Polymeric Micro-Analytical Devices Using a Laser Direct Writing Method -- Research on Fabricating Technology of Three Dimensional Integrated Braided Composite I Beam -- Simulated Annealing Genetic Algorithm and its Application in Mixed-Model Assembly Line Design -- Construction of Marketing Management Information System of Travel Agency Based on Customer Relationship Management -- Research on the Application of Fuzzy Neural Network in the Automobile Reliability -- A Multi Agent-Based Approach for Supply Chain Network -- Experiment Research of Cutter Edge and Cutting Parameters Influence on Machined Surface Roughness for High Speed Milling Hardened Steel -- Study on Laser Triangulation Measurement Principle of Three Dimensional Surface Roughness -- Estimation and Display of Triangular Mesh Curvature in Reverse Engineering -- The Optimization for Design of the Parameters of Spiral Baffle -- Feature Analysis for Milling Force of Three-Edge End Mills -- The Reliability Analysis of a Vacuum Forming Mold for IC Packing Bag -- A Non-Linear Flow Channel Implementation Method in Magnetic Gap Space of Magneto-Rheological Valve -- The Analysis of Key Influence Factors and Application Countermeasures on Quality of FDM Prototype Model -- Calculation Method for the Profile Curves of Cycloidal Pump -- Effect of Alkaline Treatment of Wood Flour on Strength of Wood-Plastic Composites for Selective Laser Sintering -- Application of Regression Analysis of Reliability Research in Off-Center Wearing on Well Tube and Rod of Oil Sucker -- A Modified Wavelet Transform Profilometry -- Simulation Study on Deep Hole Drilling Machine Hydraulic System Based on System Schematic Diagram -- Study on the Green Processing of Impeller -- Development of a Ring Permeability Test System -- The Variable Non-Linear Flow Channel Method and Device -- Research on Bearing Life Prediction Based on Three Parameters Weibull Distribution -- The Study of Target Points Center Extracting and Matching in Calibration -- The Prediction of Shot Peening's Surface Roughness with Premixed Water Jet Based on Neural Network -- Research on Safety Protection Technology of Conventional Lathe CA6140 -- Preparation and Properties of Waterborne Polyurethane with PDMS Side Chain -- Investigation of the Drawing Process of a Square Rod from a Round Bar by Using 3-D Finite Element Analysis -- Finite Element Numerical Simulation of EDM Surface Strengthening in Gas Medium of Stainless Steel 1Cr13 -- The Application and Development of Microbubble Column Flotation Technology in China -- Effects of Isothermal Process Parameters on the Microstructure of Semisolid Alsi7mg Alloy Produced by EPM -- Study on Dynamic Fuzzy Classification of Design Proposal Based on Design Style -- Analytical Study on Kinetic Characteristic of the Shell of Air-Powered Diving Pump -- Study on Variant Design and Improving Technology of Complex Mechanical Products Based on Knowledge Reuse -- Study of Modeling and Distortion Predicting for Multi-Frame Components -- The Development of Fault Diagnosis System of Reciprocating Compressor Based on LabVIEW -- The Dynamic Finite Element Analysis of Table of VM1000 CNC Machining Center -- Integration Technology and Application Research on Management Information in Textile Industry -- Flexible Wedge-Effect for Insect Flying and Fishtail-Effect for Fish Swimming -- Study on Cumulate Function of Cut-In Impacting Disrepair with Waved-Edge Milling Insert -- Preparation of V-Doped Titanium-Bearing Blast Furnace Slag and its Antibacterial Activity to Mildew -- Study on Temperature Field of Different Substrate Shape in Preparing Diamond Film -- Research on Fatigue Behaviors of Nodular Cast Iron QT800 by Laser Shock Processing -- Numerical Simulation of Thermal Deformation of High Speed and Exactitude Thermo Grip -- FTA-BN Approach to Risk Assessment of Die Casting Die and Risk Mitigation Solution in 4Ps Development Framework -- Study on Atmospheric Corrosion Behaviour of Sicp/Al Composite -- Experiment Research on Grinding of Optical Glass with Indigenously Developed Monolayer Brazed Diamond Grinding Wheel -- Open CNC System Based on Embedded Monitoring Unit -- Study on Adsorption Characteristics of Ni (II) by Palygorskite -- Experimental Study on Thermostatic Cutting Nickel-Base Superalloy GH4169 -- Research on RFID and Vision-Based AGV Navigation -- Study on Data Acquisition System for Cold Extrusion of Internal Threads Based on Virtual Instrument -- The Influence of Surface Tension on Lubrication Film Thickness and Pressure -- New Technology of Solospun and Prospect of its Application and Development -- Study of Traction Properties of Three Space Lubricants Used for Rolling Bearing.
Plný text je dostupný pouze z IP adres počítačů Univerzity Tomáše Bati ve Zlíně nebo vzdáleným přístupem pro zaměstnance a studenty
Includes bibliographical references and indexes.
International Conference on Functional Manufacturing Technologies (2nd : 2010 : Harbin, China).
Stafa-Zurich, Switzerland : Trans Tech Publications, ©2010